Design guidelines CELO Tools

Pilot hole calculator and engineer-verified 2D and 3D CAD models to integrate in your design.

3D CAD DATEN

CELO stellt 3D-Modelle unserer Hauptschrauben für die Kunststoff- und Metallmontage zur Verfügung. Nach der Registrierung können Sie die CAD-Daten wie TAPTITE 2000®, REMFORM® und FASTITE® 2000™.
3D CAD DATEN

Anfordern der Muster

Die richtige Auswahl der besten Lösung zur Materialverbindung bereits während der Produktentwurfsphase trägt zur Reduzierung der Gesamtmontagekosten bei. Die Schrauben sind aufgrund ihrer Haltbarkeit, Beständigkeit und Kosten nach wie vor das bevorzugte Verbindungsmittel.

Design-Konfigurator

CELOs Konfigurator für die Auslegung von Schraubenlöchern berechnet Kernlochdurchdimensionen von gewindeformenden Schrauben, für Kunststoff und Metall.

TAPTITE 2000® · REMFORM® · FASTITE® 2000™
Design-Konfigurator

2D-Zeichenwerkzeug

Erstellen Sie technische Zeichnungen für Schrauben nach Ihren Spezifikationen. Konfigurieren Sie Gewindetyp, Kopfform, Antrieb und Beschichtung, um CAD-Zeichnungen für Ihre Anwendung zu erstellen.
2D-Zeichenwerkzeug

Why use CELO design tools?

  • Correct hole sizing: Use the hole configuration to correctly size holes in plastic, metal, or thin sheet metal.
  • CAD models ready for integration: Download engineer-verified  3D files and 2D drawings and insert them directly into your design software, saving hours of drafting.
  • Joint Testing from the design phase: Understand how thread-formed joints behave in technical plastics and metals before ordering final molds or toolings.

Use screws with a thread design optimised for plastic assembly. A 30° flank angle — as used on REMFORM® II HS™ screws — reduces the radial stress generated during thread forming, which is the main cause of cracking in plastic housings. Pilot hole diameter and depth must also be matched to the type of plastic.

To get the correct values for your material, enter your data into the CELO online pilot hole calculator — it returns the recommended hole configuration and boss design in seconds

Both TAPTITE 2000® TRILOBULAR® screw and REMFORM® II F™ screws are suitable for direct fastening into aluminum. Their thread profile forms a strong, uniform thread into untapped holes -eliminating pre-tapping and the associated costs of using machine screw.

For aluminum extruded profiles with open C-shaped holes, REMFORM® II F™ is the recommended choice. Its round cross-section maintains full contact with the aluminum along the entire thread.

TAPTITE® screws loosening resistance requires the three lobes to stay in full contact with the nut material — where a lobe falls on the open part of the hole, that contact is lost, and with it the required resistance to loosening.

You can integrate these screws directly into your designs by downloading the 3D CAD models or configuring your 2D drawing.

As a general design rule, the outer diameter of a plastic boss should be 2.0 to 2.5 times the nominal screw diameter (Dext ≈ 2.0·d to 2.5·d). The exact ratio within this range depends on the material and the application — we recommend validating the final boss design with our application engineers. 

REMFORM® II HS™ thread design generates lower radial stress during thread forming, which allows smaller bosses than conventional thread-forming screws — reducing weight and material cost in the part.

The REMFORM® II HS™ thread design allows smaller bosses than conventional thread-forming screws — reducing weight and material cost in the part. Its profile generates lower radial stress during thread forming, making this possible.REMFORM® II HS™ screws allow for thinner bosses than standard thread-forming screws, reducing both weight and material cost in your part design.

Get a starting point for your boss design with the CELO online pilot hole calculator.